|
AES-400
Multipurpose Epoxy Coating
|
Storage &
Handling
|
| AES-400
is a 60% solids epoxy resin polyamide coating.
It was especially designed and developed to
withstand extreme conditions that will quickly destroy
conventional type protective paint coatings.
|
Typical
Uses
AES-400
is designed for adhering to almost any clean surface,
including aluminum, wood, metals of all types, plastic,
brick, glass, concrete, and masonry. AES-400 has excellent anti-corrosion qualities and sward hardness.
Recommended as an interior or exterior coating.
The few surfaces AES-400 is not recommended for
are Teflon, high-plasticized vinyl’s, polyethylene,
and silicone rubber.
|
Preparation
Surfaces
should be free of rust, mill scale, paint, algae,
grease, oil, or any other film forming foreign material.
Optimum performance and adhesion is obtained if
the surface is dry and a profile is created. Detailed preparation methods are
available through SSPC at www.sspc.org
or 412-281-2331 or NACE at www.nace.org
or 281-228-6200.
|
Mixing
The mixing of parts A & B is
very important! Material
is supplied in two containers as a unit.
Always mix a complete unit in the proportion
supplied. Agitate each part separately before combining
the two. AES-400
has a mixing ratio of 1 part “B” to 1 part “A”
(1:1). Use a jiffy mixer to thoroughly combine both parts.
Mix for at least 6 minutes and allow a one hour
idle activation time before applying or adding thinner.
This will also allow any air bubbles to escape
before application. Longer
idle activation times (not to exceed ½ the pot life)
will produce quicker dry times. |
Thinning
Thinning
is generally not necessary when applying AES-400.
Use as supplied if possible.
If thinning is necessary, especially if spraying,
thin no more than 2 quarts per gallon with Lacquer
Thinner. Addition
of thinner creates a longer pot life and increases
possibility of sag.
|
Application
Apply
AES-400 with brush, roller, or spray.
Apply at the rate of 1 gallon per 150 square feet
in order to achieve 6 dry mils film.
Keep air pressure on spray equipment as low as
possible to minimize fogging.
Vertical surfaces may require multiple coats to
avoid sag.
|
| Dry
Film Application Rate |
| To
yield dry film of: |
Apply
sq. ft. gallon |
| 3
mls. |
325
sq. ft. |
| 6
mls. |
240
sq. ft. |
| 10
mls. |
160
sq. ft. |
|
|
|
General
AES-400
should be applied in well-ventilated areas.
Surfaces should be free of foreign matter.
DO NOT apply near open flame.
|
Clean
Up
Application
equipment should be cleaned immediately with Lacquer
Thinner. Use
Apple Cider Vinegar to clean hands and skin. Do
not allow AES-400 to remain on tools or in equipment!
Once it sets and is cured, it is difficult to
remove.
|
| Curing
Time |
| Pot
Life: |
24
hrs. at 80ºF |
| Drying
Time: |
1
- 2 hrs. at 80ºF |
| Complete: |
7
days at 80ºF |
|
| Packaging |
| 2
gal. units |
|
| 1.
1 gal. can full of base |
part
"B" |
| 2.
1 gal. can full of activator |
part
"A" |
| |
|
| 5
gal. units |
|
| 1.
5 gal. pail containing 2.5 gallons of base |
part
"B" |
| 2.
5 gal. pail containing 2.5 gal. of activator |
part
"A" |
| |
|
| 10
gal. units |
|
| 1.
5 gal. pail full of base |
part
"B" |
| 2.
1 gal. pail full of activator |
part
"A" |
|
Color
AES
Standard Color (Gray and White)
|
Physical Contents
Solids
- % by weight - 60%, % by solids - 60%
|
Mixing
Ratio
1 part "A" to 1 part "B"
(1:1)
|
Adhesion-Pull-Off
(D4541):
Steel: 1357 psi
|
|
Impact
Resistance (D2794): 16 inch lbs. direct - passed
|
|
For further
assistance, contact
one of our technicians via phone or by email.
|
